Sale: 自制雲台板

頭像
Nosneb
夸克星
文章: 2814
註冊時間: 週五 12 5月, 2006 13:31
來自: 中華人民共和國 香港特別行政區

Re: Sale: 自制雲台板

文章 Nosneb » 週二 15 6月, 2010 00:54

funoooo 寫:
Nosneb 寫:
funoooo 寫:處理: 做了熱處理加工 (Heat Treatment)
請問是做了哪一類熱處理? 回火, 退火?
Nosneb,

你的問題怪怪他。 :shock:
回火是熱處理一個工序。
退火不是熱處理一部份。

熱處理一般分三部份:預熱,淬火,及回火。
一般淬火温度 700~1000 度.
預熱及回火就是 200~300 度.

退火返過來是減低硬度和除應力之用。 :shock:
凡於金屬加熱或冷卻, 目的使金屬改變特性如提升/降低強度,除去應力... 都係叫做熱處理(中一那年金工堂學的). 那為什麼退火(annealing)不是熱處理的一部份 :roll: 我想你的意思是 "退火不是熱處理加硬的一部份" 吧 :wink:

另想請教, 我有一件尺寸跟你這雲台板差不多大少的titaniam平板料, 厚1.5mm. 唔知有乜辦法可以加工....如鑽孔. 如果搞得掂, 我想可能會比你呢塊還輕 :twisted: :twisted:

頭像
funoooo
夸克星
文章: 7831
註冊時間: 週五 30 6月, 2006 16:34
聯繫:

Re: Sale: 自制雲台板

文章 funoooo » 週二 15 6月, 2010 20:17

Nosneb 寫:
funoooo 寫:
Nosneb 寫:
funoooo 寫:處理: 做了熱處理加工 (Heat Treatment)
請問是做了哪一類熱處理? 回火, 退火?
Nosneb,

你的問題怪怪他。 :shock:
回火是熱處理一個工序。
退火不是熱處理一部份。

熱處理一般分三部份:預熱,淬火,及回火。
一般淬火温度 700~1000 度.
預熱及回火就是 200~300 度.

退火返過來是減低硬度和除應力之用。 :shock:
凡於金屬加熱或冷卻, 目的使金屬改變特性如提升/降低強度,除去應力... 都係叫做熱處理(中一那年金工堂學的). 那為什麼退火(annealing)不是熱處理的一部份 :roll: 我想你的意思是 "退火不是熱處理加硬的一部份" 吧 :wink:

另想請教, 我有一件尺寸跟你這雲台板差不多大少的titaniam平板料, 厚1.5mm. 唔知有乜辦法可以加工....如鑽孔. 如果搞得掂, 我想可能會比你呢塊還輕 :twisted: :twisted:
大佬, titanium 都比你找到. 好嘢!
你想加工.嘿嘿..... 它比我那些再硬點. 好似 68~72 HRC. 需要特別加工.而且很貴. :shock: :shock: :shock: Good Luck.!

頭像
Nosneb
夸克星
文章: 2814
註冊時間: 週五 12 5月, 2006 13:31
來自: 中華人民共和國 香港特別行政區

Re: Sale: 自制雲台板

文章 Nosneb » 週二 15 6月, 2010 21:56

funoooo 寫:大佬, titanium 都比你找到. 好嘢!
你想加工.嘿嘿..... 它比我那些再硬點. 好似 68~72 HRC. 需要特別加工.而且很貴. :shock: :shock: :shock: Good Luck.!
嘿嘿~~ 當年因為想DIY部水冷機俾缸熱帶魚用, 因為係咸水, 所以一定要用鈦. 好似係當時我上一個大陸的關於tatanium的forum到問人問題, 跟住就有人同我聯系, 我做好圖紙匯完錢兩個禮拜就收到貨喇, 丫.... 我記得塊板係有十個3.5mm孔. 因為冇辦法自行加工, 所以而家兩塊鈦片都閣在一旁 :cry:

syyuen168
夸克星
文章: 3856
註冊時間: 週五 06 7月, 2007 23:06

文章 syyuen168 » 週二 15 6月, 2010 22:13

Benson, What do you want to do with your Ti ? send me a pm. I maybe able to help you. I have some vendors who process titanium racks for anodizing. Now, Ti is a very light and stable metal and only flouride can eat it away. It is a very difficult metal to process also a metal that has "no memeory"(When Ti is subject to a force of blending or a torque, it returns to its original form promptly, it can be an advantage or di-advantage depending on your application) :D :D

頭像
Nosneb
夸克星
文章: 2814
註冊時間: 週五 12 5月, 2006 13:31
來自: 中華人民共和國 香港特別行政區

文章 Nosneb » 週三 16 6月, 2010 01:22

syyuen168 寫:Benson, What do you want to do with your Ti ? send me a pm. I maybe able to help you. I have some vendors who process titanium racks for anodizing. Now, Ti is a very light and stable metal and only flouride can eat it away. It is a very difficult metal to process also a metal that has "no memeory"(When Ti is subject to a force of blending or a torque, it returns to its original form promptly, it can be an advantage or di-advantage depending on your application) :D :D
先謝過袁生!! 本來就係諗住用黎做魚缸水冷, 後來失敗左. 見到奴老板呢個post又勾起我用呢塊Ti板做雲台板既念頭. 不過如以加工方便性為前提, 我想還是用鋁合金比較易食. 將來有必要就找你幫忙 8) 8) thanks!

頭像
funoooo
夸克星
文章: 7831
註冊時間: 週五 30 6月, 2006 16:34
聯繫:

文章 funoooo » 週五 18 6月, 2010 10:00

Nosneb 寫:
syyuen168 寫:Benson, What do you want to do with your Ti ? send me a pm. I maybe able to help you. I have some vendors who process titanium racks for anodizing. Now, Ti is a very light and stable metal and only flouride can eat it away. It is a very difficult metal to process also a metal that has "no memeory"(When Ti is subject to a force of blending or a torque, it returns to its original form promptly, it can be an advantage or di-advantage depending on your application) :D :D
先謝過袁生!! 本來就係諗住用黎做魚缸水冷, 後來失敗左. 見到奴老板呢個post又勾起我用呢塊Ti板做雲台板既念頭. 不過如以加工方便性為前提, 我想還是用鋁合金比較易食. 將來有必要就找你幫忙 8) 8) thanks!
Nosneb, 不要浪費啦!Ti 扳放在一邊,不如加工成為雲臺板好過啦!好難得有 Ti 雲臺。一定又實用又型仔。 :twisted:

syyuen168
夸克星
文章: 3856
註冊時間: 週五 06 7月, 2007 23:06

文章 syyuen168 » 週五 18 6月, 2010 10:20

I could not agree more. Boss Funooo is right this time. :mrgreen: :mrgreen:
funoooo 寫:
Nosneb 寫:
syyuen168 寫:Benson, What do you want to do with your Ti ? send me a pm. I maybe able to help you. I have some vendors who process titanium racks for anodizing. Now, Ti is a very light and stable metal and only flouride can eat it away. It is a very difficult metal to process also a metal that has "no memeory"(When Ti is subject to a force of blending or a torque, it returns to its original form promptly, it can be an advantage or di-advantage depending on your application) :D :D
先謝過袁生!! 本來就係諗住用黎做魚缸水冷, 後來失敗左. 見到奴老板呢個post又勾起我用呢塊Ti板做雲台板既念頭. 不過如以加工方便性為前提, 我想還是用鋁合金比較易食. 將來有必要就找你幫忙 8) 8) thanks!
Nosneb, 不要浪費啦!Ti 扳放在一邊,不如加工成為雲臺板好過啦!好難得有 Ti 雲臺。一定又實用又型仔。 :twisted:

頭像
Nosneb
夸克星
文章: 2814
註冊時間: 週五 12 5月, 2006 13:31
來自: 中華人民共和國 香港特別行政區

文章 Nosneb » 週五 18 6月, 2010 11:15

嘿嘿.... 其實塊板只得1.5mm厚(可能係1mm添 :twisted: ) 雖然沒有"記憶" 但始終都係唔夠硬. 孭導星鏡我諗頂多唔多以超過1kg, 否則就會彈下彈下. 之但係如果塊鈦板係厚2.5mm的話我想我掂都會死掂佢做雲台板 :evil: 遲下摷返出黎, 有機會就帶出黎比大家研究研究

回覆文章

回到「觀星者天文儀器社」

誰在線上

正在瀏覽這個版面的使用者:沒有註冊會員 和 1 位訪客