望遠鏡設計軟件

自製天文望遠鏡 牛頓望遠鏡 杜蘇式 卡式 設計和磨鏡方法<br>
佛科試鏡法 佛科刀片儀 光柵試鏡法 光柵片
回覆文章
頭像
Wah!
夸克星
文章: 9073
註冊時間: 週六 28 6月, 2003 01:19
聯繫:

望遠鏡設計軟件

文章 Wah! » 週五 25 3月, 2005 02:29

MODAS是著名的免費光學設計軟件,並有專門為自製鏡而設的計算工具TMT Calculator.

http://members.kabsi.at/i.krastev/download.html

===============

http://www.myoptics.at/

http://www.atmos-software.it/Atmos.html#des_slides

updated by Wongsir
2010-11-23

頭像
ffmak
星際雲
文章: 10
註冊時間: 週二 15 3月, 2005 14:03

文章 ffmak » 週五 25 3月, 2005 16:55

Another good website... Many resources...
http://jhpw.phys.ntu.edu.tw/html/atm.html

頭像
ffmak
星際雲
文章: 10
註冊時間: 週二 15 3月, 2005 14:03

文章 ffmak » 週五 25 3月, 2005 17:50

NEWTONIAN TELESCOPE DESIGN PLANNER
http://www.catseyecollimation.com/designie5.html

頭像
獵戶四十二
主序星
文章: 214
註冊時間: 週日 07 11月, 2004 23:50

文章 獵戶四十二 » 週日 27 3月, 2005 02:27

哇, 原來連望遠鏡設計軟件都有呀?
多謝兩位介紹啊, 如果唔係我真係唔會知~
睇睇有咩學先, 多謝曬兩位^^

頭像
Wah!!
夸克星
文章: 13283
註冊時間: 週一 15 3月, 2004 21:28
聯繫:

文章 Wah!! » 週三 21 2月, 2007 11:21

一個好快速方便的卡式望遠鏡設計程式.

資料來源
附加檔案
1147650-CassDesign.zip
版權由原作者 Mike I. Jones 持有
Mike I. Jones All rights reserved
(26.65 KiB) 已下載 2811 次

頭像
XR250
夸克星
文章: 6513
註冊時間: 週一 13 12月, 2004 09:43
來自: NT

文章 XR250 » 週三 21 2月, 2007 15:34

好奇一問,如果造一枝8吋f15的classical cassegrain用來睇或用toucam拍攝行星,會唔會好過f10的c8好多呢?

頭像
Wah!!
夸克星
文章: 13283
註冊時間: 週一 15 3月, 2004 21:28
聯繫:

文章 Wah!! » 週三 21 2月, 2007 15:41

我估唔會好好多, 始終 C8 都唔一支差的望遠鏡, 距離繞射極限都唔係太遠.
C8 輸的主要係反差, 影行星可以做後期處理, 應該唔太大影響吧?

頭像
XR250
夸克星
文章: 6513
註冊時間: 週一 13 12月, 2004 09:43
來自: NT

文章 XR250 » 週三 21 2月, 2007 15:56

咁又係,如果用來影行星,C8雖然唔係最好,但都係其中一枝好鏡。

唔知幾時有機會睇到 CN212 vs Mewlon210 vs VMC200L vs VC200L vs C8 vs M8呢?

Hay
主序星
文章: 178
註冊時間: 週五 12 5月, 2006 01:32

Re: 望遠鏡設計軟件

文章 Hay » 週四 22 2月, 2007 03:15

Wah! 寫:MODAS是著名的免費光學設計軟件,並有專門為自製鏡而設的計算工具TMT Calculator.

http://members.kabsi.at/i.krastev/download.html
見到Wah! 介紹呢個光學設計軟件,記起早前睇過一個ATM 網站入邊有講自製不同的望遠鏡,有牛頓式、RC等等,有D都有用S/W 去設計,各位可以睇下

http://www.deep-sky.co.uk/telescopemaking.htm

另外其中3 of the Best 介紹o既望遠鏡有靚又有簡單的,都要睇睇 :D

Hay

BJDF
主序星
文章: 143
註冊時間: 週日 26 2月, 2006 10:52
來自: 北京

文章 BJDF » 週日 07 10月, 2007 19:59

有中文计算软件嘛?那位同好介绍一个。

Chanlunlun
夸克星
文章: 3847
註冊時間: 週四 09 10月, 2003 21:06

文章 Chanlunlun » 週日 07 10月, 2007 21:35

XR250 寫:好奇一問,如果造一枝8吋f15的classical cassegrain用來睇或用toucam拍攝行星,會唔會好過f10的c8好多呢?
Dear Mr. 250,

Aperture to aperture a Cassegrain is doomed to be far inferior than a Newtonian for the following reasons :-

1. high central obstruction - nothing can beat a Newtonian in this respect. No matter it is a SCT, Classical Cassegrain or RC, the central obstaruction are bound to be 25% or higher comparing to 20% or less for a Newtonian.

2. Magnification factor of the secondatry - most Cassegrain's secondary has a magnification ratio of 4 to 5 times which means than the error of the primary, if any, will be magnifiied by same amount. Most primaries for Classical Cassegrain are fast paraboloid which means that it's very difficult to guarantee its surafce precision. Newtionian, on the other hand, has a very great advantage of being better chance of being equipped with primary of much higher quality due to the relative ease of facbricating precision paraboloidal mirror of high f/number. One exception is the Schmidt Cassegrin and Maksotov where they employ spherical prinmary which is very easy to manufacture to very high smoothness and precision.

So if you are considering yourselves a planetary shooting feverist my advice is to stick to a long Newtonian or simply use a C-11. A Maksotov is also a very good choice but I'm afraid that a big one will empty your wallet quite soon.

Best regards
Chan Yuk Lun

sbod

文章 sbod » 週日 07 10月, 2007 21:37

BJDF 寫:有中文计算软件嘛?那位同好介绍一个。
這可能要找人把軟件中文化了. :?

頭像
Wah!!
夸克星
文章: 13283
註冊時間: 週一 15 3月, 2004 21:28
聯繫:

文章 Wah!! » 週日 07 10月, 2007 21:47

BJDF 寫:有中文计算软件嘛?那位同好介绍一个。
望遠鏡設計的常用的詞語應該不會太多, 記住這幾個詞的英文就有好多軟件可以選擇, 順便多學幾個英文, 一舉兩得 ;)
不懂的詞語可以查字典, 或者在論壇裏問網友, 相信大家都會很樂意幫忙.

頭像
Wah!!
夸克星
文章: 13283
註冊時間: 週一 15 3月, 2004 21:28
聯繫:

文章 Wah!! » 週二 11 11月, 2008 10:16

http://www.davidlewistoronto.com/plop/
http://www.davidlewistoronto.com/guiplop_3d.htm

著名的頂級浮動支撐主鏡座設計軟件 PLOP 最近作出更新.
最新支援 Z88 計算, 可以用3D模型對於不同厚度的主鏡計算誤差的大小.

圖檔
圖檔

Version 3.0.1 Nov 1 2008

- remembers glued or sling in the control file (this will break old files)
- z88 is disabled until file is generated
- z88 prints message to let you know it is running

Version 3.0.0 Sept 2008

- now supports 3 D modeling using Z88
- can model slings or mirror glued to cell when the cell is tilted
- can copy pictures to clipboard
- parts now include a label to tell which corner is which to orient the parts
- part dimensions can be saved to image file
- uses less memory and runs faster for large designs

回覆文章

回到「自製天文望遠鏡 Amateur Telescope Making 」

誰在線上

正在瀏覽這個版面的使用者:沒有註冊會員 和 3 位訪客